...
- Connect an Ethernet patch lead from the source SmartServer IoT's RJ45 LAN connector to an Ethernet switch port on your local LAN with a DHCP server running (unless you are using a static IP address).
- Connect your PC to the same LAN and subnet as the source SmartServer IoT using an Ethernet lead. Alternatively, use the SmartServer's Rapid Fallback feature (if enabled) to set the SmartServer IoT's address to 192.168.1.222, which will allow a direct Ethernet connection from the PC to the SmartServer IoT. In this case you will have to manually configure the PC to be on the same subnet as the source SmartServer IoT.
- Remove any USB devices from the source SmartServer.
- Connect the terminal emulator to the console port using a USB cable and power up the SmartServer.
Find the SmartServer IoT's IPV4 address for the eth0 port (shown as inet addr:192.168.168.5 in the example below, third line) by entering the following command at the console:
ifconfig
A result similar to the following appears:Code Block apollo@smartserver-17q41xs:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:d0:71:07:46:eb inet addr:192.168.168.5 Bcast:192.168.168.255 Mask:255.255.255.0 inet6 addr: fe80::2d0:71ff:fe07:46eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38427 errors:0 dropped:17168 overruns:0 frame:0 TX packets:35507 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2909558 (2.9 MB) TX bytes:6099630 (6.0 MB) Interrupt:51 Base address:0x6000 eth1 Link encap:Ethernet HWaddr 00:d0:71:07:46:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:50 Base address:0xe000 ip70 Link encap:Ethernet HWaddr 00:d0:71:07:6f:50 inet addr:192.168.239.128 Bcast:192.168.239.255 Mask:255.255.255.0 inet6 addr: fe80::2d0:71ff:fe07:6f50/64 Scope:Link UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6538 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:380111 (380.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1 RX packets:1230995 errors:0 dropped:0 overruns:0 frame:0 TX packets:1230995 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:170737328 (170.7 MB) TX bytes:170737328 (170.7 MB) apollo@smartserver-17q41xs:~$
- Connect to the source SmartServer IoT's CMS from a browser /wiki/spaces/TEMP/pages/44041710 at:
- With SmartServer release 2.8 or higher: https://<IPV4 address>/cms
- With SmartServer release prior to 2.8: https://<IPV4 address>:8443/cms
The CMS login window appears.
- Login using the username and password. Note that the username is always apollo, but the password may have been changed from the one that is printed on the rear label of the SmartServer.
Open the Storage widget.
Note Note 1: If the Storage widget does not appear on the CMS, you will need to add it to the dashboard /wiki/spaces/TEMP/pages/44631776.
Note 2: To best view all of the information on this widget, click the Expand button (
).Click BACKUP.
Click BACKUP SYSTEM in the Confirmation dialog box.
- Click OK in the Confirmation dialog box to start the backup process.
...
- Connect an Ethernet patch lead from the target SmartServer's RJ45 LAN connector to an Ethernet switch port on your local LAN with a DHCP server running (this assumes a new SmartServer).
Connect your PC to the same subnet as the target SmartServer using an Ethernet lead. Alternatively, use the SmartServer's Rapid Fallback feature to set the SmartServer's address to 192.168.1.222, which will allow a direct Ethernet connection from the PC to the SmartServer.
Remove any USB devices from the target SmartServer.
Connect the terminal emulator to the console port using a USB cable and power-up the SmartServer.
- Find the SmartServer's IPV4 address by entering the following command at the console:
ifconfig
- Connect to the source SmartServer IoT's CMS from a browser /wiki/spaces/TEMP/pages/44041710 at:
- With SmartServer release 2.8 or higher: https://<IPV4 address>/cms
- With SmartServer release prior to 2.8: https://<IPV4 address>:8443/cms
The CMS login window appears.
- Login using the username and password. Note that the username is always apollo, but the password may have been changed from the one that is printed on the rear label of the SmartServer.
Open the Storage widget.
Note Note 1: If the Storage widget does not appear on the CMS, you will need to add it to the dashboard /wiki/spaces/TEMP/pages/44631776.
Note 2: To best view all of the information on this widget, click the Expand button (
).Click RESTORE.
Select the CLONE tab on the Restore dialog box and select the backup file that was copied to the SD Card from the drop-down menu as shown in the example below.
Warning title Warnings Cloning preserves the new SmartServer's Serial Number, Host Name, and Install Code, but changes the apollo password to the old SmartServer's password, as well as the SID and MAC Addresses. A target SmartServer should not be cloned with the same backup file more than once. You cannot put two SmartServer clones on the same network.
- Click RESTORE.
Click OK in the Confirmation dialog box to start the restore process.
Messages similar to the following will appear on the console:
Code Block Broadcast message from rebootmanager daemon (Tue 2020-03-10 15:15:02 BST) System going down to perform restore... going down for reboot NOW ==================================================================== ============ Adesto Apollo 2 Backup/Restore Utility ============== ==================================================================== Version 1.2 * Initializing... OK SDCard: /dev/mmcblk2p1 * Checking required files... file 'restore' is present. file 'preserve' is present. file backups/SmartServer-System-Backup-2020-03-10-114532.tgz is present. Required files are present. * Checking files integrity... e77de975a4eabefc339dae6f132d8803 - OK Files validated. * Mounting partitions... OK Filesystem 1K-blocks Used Available Use% Mounted on none 868600 0 868600 0% /dev /dev/mmcblk2p1 30634944 1935896 27119836 7% /mnt/mmc_restore /dev/mmcblk3p2 3232312 2164084 884320 71% /mnt/mmc_main /dev/mmcblk3p1 16128 8707 7422 54% /mnt/mmc_main/boot /dev/mmcblk3p5 884676 7268 815252 1% /mnt/mmc_main/var/apollo * Preserving Identity...OK * Unmounting partitions... OK * Formatting partitions... * Mounting partitions... OK Filesystem 1K-blocks Used Available Use% Mounted on none 868600 0 868600 0% /dev /dev/mmcblk2p1 30634944 1935932 27119800 7% /mnt/mmc_restore /dev/mmcblk3p2 3232312 5756 3042648 0% /mnt/mmc_main /dev/mmcblk3p1 16128 1 16128 0% /mnt/mmc_main/boot /dev/mmcblk3p5 884676 904 821616 0% /mnt/mmc_main/var/apollo Always mount sdcard for restore. * Restoring System... OK * Restoring original identity...OK * Syncing... OK * Unmounting partitions... OK Procedure Complete. Rebooting in 5 seconds...
To ensure full functionality after the reboot process completes, perform the following steps:
Power-cycle the target SmartServer to ensure full functionality.
Note Note: The target SmartServer may not be accessible over the current IP infrastructure due to IP address changes, and its password will have changed to that of the source SmartServer. - Verify target SmartServer operations.
...