| Info |
|---|
For SmartServer 3.4 and higher, see Backing Up, Restoring, and Cloning the SmartServer. |
The SmartServer ships with an SD Card inserted into the appropriate slot on the device. The CMS database is located on the SD Card. This SD Card must remain inserted in the SmartServer whenever power is applied to the SmartServer.
The CMS Storage widget provides the ability to view system information including internal flash memory, CPU utilization, and log sizes, as well as to perform system and database backup, restore, and cloning operations. It also provides the ability to change logging settings (data and/or event logging, and storing on an SD Card).
...
Open the Storage widget.
Note Note: To best view all of the information on this widget, click the Expand button /wiki/spaces/TEMP/pages/44631776 ( 
). 
- Click the Edit button (
). 
Note that the Edit button changes to a Save button (
).
- Select the appropriate checkbox (that is, Save data logging, Save event logging, and/or Store on the SD Card).
- Click the Save button () for logging changes to take effect.
The new logging settings are stored in the Storage widget.
...
Open the Storage widget.
Note Note: To best view all of the information on this widget, click the Expand button /wiki/spaces/TEMP/pages/44631776 ( ). 
- Click BACKUP.
A confirmation dialog box appears.
- Select BACKUP SYSTEM or BACKUP DATABASE for the backup operation.
A message similar to the following appears:
System backup
Database backup - Click OK to proceed with the desired backup operation.
...
To restore a backup to a new SmartServer, remove power from the new SmartServer.
Remove the SD Card from the SmartServer.
Insert your SD Card with the backup image to be restored into the SmartServer.
Open the Storage widget.
Note Note: To best view all of the information on this widget, click the Expand button /wiki/spaces/TEMP/pages/44631776 ( ). Click RESTORE.
The Restore dialog box appears displaying the name of the system image to be restored.
Use the SYSTEM and DATABASE tabs to select the type of restore operation you want to perform.
System restore
Database restore
If more than one file is available, a dropdown list will appear allowing you to select the desired file as shown in the example below.
Dropdown list for a system restore with multiple backup files
Dropdown list for a database restore with multiple backup files- If multiple backup files are available, then select the file you want to use from the dropdown list for the restore operation.
Multiple system files example
Multiple database files example Click RESTORE to proceed with the restore operation.
Warning This feature overwrites the new SmartServer's Serial Number, Host Name, MAC Addresses, Install Code, SID, and apollo password.
A message similar to the following appears:
System restore
Database restore- Click OK to proceed with the desired restore operation.
...
Open the Storage widget.
Note Note: To best view all of the information on this widget, click the Expand button /wiki/spaces/TEMP/pages/44631776 ( ). Click RESTORE.
The Restore dialog box appears.
Select the CLONE tab on the Restore dialog box.
The Restore dialog box appears displaying the name of the system backup file to be used for the target SmartServer.
If more than one file is available, a dropdown list will appear allowing you to select the desired file as shown in the example below.
- If multiple backup files are available, then select the file you want to use from the dropdown list for the clone operation.
Click RESTORE.
Warning title Warnings This feature preserves the new SmartServer's Serial Number, Host Name, and Install Code, but changes the apollo password, MAC Addresses, and SID. A target SmartServer should not be cloned with the same backup file more than once. You cannot put two SmartServer clones on the same network.
A confirmation dialog box appears.
Click OK in the Confirmation dialog box to start the cloning process.
Messages similar to the following will appear on the console:No Format Broadcast message from rebootmanager daemon (Tue 2020-03-10 15:15:02 BST) System going down to perform restore... going down for reboot NOW ==================================================================== ============ Adesto Apollo 2 Backup/Restore Utility ============== ==================================================================== Version 1.2 * Initializing... OK SDCard: /dev/mmcblk2p1 * Checking required files... file 'restore' is present. file 'preserve' is present. file backups/SmartServer-System-Backup-2020-03-10-114532.tgz is present. Required files are present. * Checking files integrity... e77de975a4eabefc339dae6f132d8803 - OK Files validated. * Mounting partitions... OK Filesystem 1K-blocks Used Available Use% Mounted on none 868600 0 868600 0% /dev /dev/mmcblk2p1 30634944 1935896 27119836 7% /mnt/mmc_restore /dev/mmcblk3p2 3232312 2164084 884320 71% /mnt/mmc_main /dev/mmcblk3p1 16128 8707 7422 54% /mnt/mmc_main/boot /dev/mmcblk3p5 884676 7268 815252 1% /mnt/mmc_main/var/apollo * Preserving Identity...OK * Unmounting partitions... OK * Formatting partitions... * Mounting partitions... OK Filesystem 1K-blocks Used Available Use% Mounted on none 868600 0 868600 0% /dev /dev/mmcblk2p1 30634944 1935932 27119800 7% /mnt/mmc_restore /dev/mmcblk3p2 3232312 5756 3042648 0% /mnt/mmc_main /dev/mmcblk3p1 16128 1 16128 0% /mnt/mmc_main/boot /dev/mmcblk3p5 884676 904 821616 0% /mnt/mmc_main/var/apollo Always mount sdcard for restore. * Restoring System... OK * Restoring original identity...OK * Syncing... OK * Unmounting partitions... OK Procedure Complete. Rebooting in 5 seconds...
To ensure full functionality after the reboot process completes, perform the following steps:
Power-cycle the target SmartServer IoT to ensure full functionality.
Note Note: The target SmartServer IoT may not be accessible over the current IP infrastructure due to IP address changes, and that its password may have changed to that of the source SmartServer IoT. - Verify target SmartServer IoT operations.