...
The SmartServer Configuration page provides the ability to configure the SmartServer system and network and system settings, as well as LON (not available for SmartServer PiLON is supported for SmartConnect 4.3 and higher, with the exception of LON PL), BACnet, OPC UA (not supported for SmartServer Pi), RS-485, Modbusfor SmartConnect 4.2 and higher, OPC UA is beta), Modbus, RS-485, EnOcean, LoRaWAN, and Firewall (IAP/MQ server) settings. The Firewall tab is not available for SmartConnect.
To view your SmartServer system information, perform the following steps:
For SmartServer IoT, open the SmartServer Configuration page as described in Accessing the SmartServer IoT Configuration Page.
...
The Network tab appears as the default SmartServer Configuration page.
...
Once the network settings are configured for the SmartServer system, then the System tab will appear as the default as shown in the next step.
For
...
SmartConnect,
...
open the SmartServer Configuration page as described in Accessing the
...
...
The Configuration tab that appears depends on your cache data. As needed, click the SmartServer IoT tab.
...
The System tab (top) will appear as the default as shown in the next step.
...
Click the System tab. The System Configuration page appears with the system information displayed at the top of the page. The system information includes the following:
Version – version of the SmartServer software that is running
Serial number – SmartServer IoT serial number (not available for
SmartServer PiSmartConnect)
MAC ID – unique ID used for SmartServer Configuration page System and LON tabs. The LON
tab is not available for SmartServer Piis supported with SmartConnect 4.3 and higher, with the exception of LON PL.
Install Code – part of the
SmartServer PiSmartConnect hostname, where hostname uses the format smartserver-<install code>
, for example. Example: smartserver-hsbcw69
Segment Provisioning Status – provisioned or unprovisioned
Segment ID – the Segment Identifier (SID) is the logical address of the device that controls a segment
LON Network Management Mode – Device Management Mode or Independent Management Mode (not available for
SmartServer PiSmartConnect)
CMS Status – provides status information about whether or not the CMS is running (not available for
SmartServer PiSmartConnect 4.2)
System Uptime – length of time that the system has been running
...
...
Refer to the table below for more information and System Configuration page references:
Topic | References and Notes |
|---|---|
Using the System Configuration page | |
Changing passwords | Managing Passwords in the (Optional) Secure Your SmartServer |
...
section |
Configuring LON network management mode |
...
...
For more information about changing passwords, see Managing Passwords in the (Optional) Secure Your SmartServer section.
For more information about rebooting the system, see Rebooting Your SmartServer. For SmartServer Pi, see Rebooting Your SmartServer Pi.
...
LON is supported for SmartConnect 4.3 and higher, with the exception of LON PL. | |
Rebooting the system | For SmartServer IoT, see Rebooting Your SmartServer IoT. For SmartConnect, see Rebooting Your SmartConnect. |
Reseting the system to defaults | For SmartServer IoT, see Resetting the SmartServer IoT to Factory Defaults. |
...
For SmartConnect, see Resetting SmartConnect to Factory Defaults. | |
Updating the system | For SmartServer IoT, see Updating or Re-imaging the SmartServer IoT. For |
...
SmartConnect, see Updating |
...
...
Downloading logs | This feature is not supported for SmartConnect 4.2. |
Configuring Advanced Intrusion Detection Environment (AIDE) | Configuring Advanced Intrusion Detection Environment (AIDE) This feature is not |
...
available for |
...
SmartConnect. |
...
Configuring HTTP proxy |
...
...
Using SmartSupervisor (Remote CMS) |